Transcription

Quick Set-up and User GuideBT Conferencing Unit X300Professional conferencing unit with wireless microphones

2Important – please read first Only use the telephone line cord, power supply cables and rechargeable batteriessupplied with your conferencing unit. Make sure the power supply is connected to a known working socket. Make sure you activate the batteries by pulling the battery pull tab and chargethe wireless microphone batteries for eight hours before using them, see page 5. To make sure you get the best range and reception from your conferencing unit,avoid interference by placing the base unit away from large metal objects suchas metal cabinets, microwave ovens or electronic products such as computersand TVs. If you’re using this product on a PSTN line you need to change the setting to PBXmode Off, see page 33.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

Check box contents32 x wireless mic unitsBase unitPhone line cord6 metreconnector cable2 x 3.7V 240mAhLi-ion Polymer batteries(already in wireless mic units)Connection boxMains power adaptor(item code 075566)ImportantOnly use the mains power adaptor, cables and rechargeable batteries supplied in this box or this productmight not work. Any replacement rechargeable batteries must be of the same type. BT accepts noresponsibility for damage caused to your conferencing unit if you use any other type of batteries.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

4Quick set-up guideWhere to put yourconferencing unit Place the base unitwithin 6 metres of a mainspower socket so the cableswill reach. Make sure it’s at least ametre away from otherelectrical appliances to avoidinterference. Don’t place the wireless micsor base unit in a bathroom orother humid area. The product works bysending radio signalsbetween the wireless micsand base unit. The strengthof the signal depends onwhere you position thebase unit.1 Plug in cables1321. Plug the 6 metre connector cable into the base unitand the other end into the connection box’s socketlabelled To Base.2. Plug one end of the phone line cord into theconnection box’s socket labelled To Line and theother end into the phone line wall socket.3. Plug the end of the mains power adaptor into theconnection box and the other end into the wallpower socket and switch on.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

Quick set-up guide2 Set up wireless mic units1. Activate the battery in each wireless mic by pullingthe plastic tab away from the back of the unit.Broadband on your phone line?Make sure you use an ADSLfilter between the phone linecord and your phone wallsocket. You can get BT ADSLmicrofilters from bt.com/shopIf you use BT Infinity youwill not need to use an ADSLmicrofilter. For other types ofbroadband, please check withyour provider if a microfilteris required.Rechargeable batteryalready fittedRemove this taband charge batteryfor 8 hours before use.If the mic unit doesn’t turn on when the pulltab is removed, take the battery out andre-insert it.2. Put each wireless mic unit on the base unit tocharge for 8 hours.Each mic unit has a red light when it’s sitting in thepowered-up base unit.When a mic unit is sitting in thepowered-up base, its light isred when charging and amberwhen fully charged.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp5

6Quick set-up guideRemoving the batteriesSlide open the battery compartment cover. Place afinger under the battery at the edge of the batterycompartment and lift it up to remove.Talk/standby timeUnder ideal conditions, thewireless mic batteries shouldgive up to 5 hours talk time or70 hours standby on a single8 hour charge.Battery low warningThe wireless mic’s red lowbattery light will flash when thebattery is low. Place the mic onthe base unit to re-charge.3 Set date and time1.2.3.4.How to change the date and timePress when the base unit isn’t in use.Press or to scroll and find Set Date/Time,then press .Press or to scroll and find the date, then press, or use the keypad to enter a two-digit number(01-31).Press or to scroll and find the month, thenpress , or use the keypad to enter a two-digitnumber (01-12).If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

Quick set-up guide5. Press or to scroll and find the year, then press, or use the keypad to enter a two-digit number(00-99) and press .6. Press or to scroll and find the hour, then press, or use the keypad to enter a two-digit number(01-24).7. Press or to scroll and find the minute, thenpress , or use the keypad to enter a two-digitnumber (00-59).8. Press or to scroll and find AM or PM.9. Press to save.PBX ModeMake sure the PBX mode is set correctly. This willdepend on whether you are using the unit on a PBXor PSTN line.The unit is set by default to PBX mode On.If you’re using the unit on a PBX, no action isrequired. If you’re using the unit on a PSTN line,then you need to change the setting toPBX mode Off. See page 33 for further details.And that’s it. Your BT ConferencingUnit X300 is ready to use.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp7

8In this guideGetting to know your conferencing unitBase unit . 10Wireless mics . 12Light status indicators . 14Menu map. 15Using your conferencing unitMake a call . 16Preparatory dialling . 16Answer a call . 16End a call. 16Redial last call. 16Adjust volume . 16Mute. 17Silence the ringer . 17Call waiting . 17Redial list . 18About the redial list. 18See the redial list . 18Dial a redial list entry. 18Save a redial list entry to yourphonebook. 18Delete a redial list entry. 19Delete all redial list entries . 19How to get a number from the callslist or phonebook, whilst on a call . 20How to get a number from theredial list while on a call. 20Page all microphones . 20PhonebookAdd a phonebook entry. 21Character map . 22Search your phonebook . 22Call someone in your phonebook . 23Edit a phonebook entry . 23Add phonebook entry to speed dial . 24Save a speed dial entry . 24Dial a speed dial number . 24Delete a speed dial entry . 25If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

In this guideCaller Display and the calls listAbout caller display. 26Calls list . 26View and dial from the calls list . 27Delete a calls list entry/all entries . 27Caller display screen messages . 27SettingsHow to change your settings . 28Menu . 28Volume . 28Ringer tone . 29Date and time . 30How to rename your base unit . 31Key tone . 32Dial mode. 32PBX mode . 33Turn PBX off . 33Set an access code . 34Reset . 35De-register and re-register thewireless mics . 36Help . 37General informationSafety information . 40How to recycle your equipment . 41Guarantee . 41Technical information . 42R&TTE . 43If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp9

10Getting to know your conferencing unitBase unitCalls List orWhen idle, press to see calls list (see page 26). In menu, phonebook,calls or redial list, press to scroll up. When entering names ornumbers, press to move the cursor to the right.Phone Book orWhen idle, press to see phonebook (see page 21). In menu,phonebook, calls or redial list, press to scroll down. When enteringnames or numbers, press to move the cursor to the left.RPress R to answer an incoming call during a callwhen you receive a call-waiting alert (see page 17).RedialPress to see a list of the calls you’ve dialled (see page 18).Mute AllPress to mute or unmute all microphones in use during a call(see page 16).If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

Getting to know your conferencing unitLightsLights are green during a call, red when mute is on or flashinggreen when there’s an incoming call, (see page 14 for full lightstatus indications).OKPress OK for the menu, to select an item or save an entry or setting.CPress C to go back or delete a character.Press and hold to delete all characters.Vol. Press to increase ringer or speaker volume.Vol. Press to decrease ringer or speaker volume.Talk/end callPress to make, answer or end a call.0Press and hold to insert either a dialing pause (P) when enteringnumbers or a space while editing names.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp11

12Getting to know your conferencing unitWireless micsThere is one fixed microphone in the base, but you can also place the two wirelessmics around the table which would be of benefit if you are sitting around a largeconference table.Mute AllPress to mute or unmute allmicrophones during a call.(when mics are on thebase they are muted).LEDThe light changes colourbetween green, amber andred. See page 14 for fulllight status indicators.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

Getting to know your conferencing unitHow to mute or unmutePressto mute or unmute all microphones. Whenthe mics are on the base unit they are muted.How long do the batteries last?Use only the batteries that come with yourconferencing unit or their equivalent. A wireless micunit will last about five hours (in use, e.g. talking) orabout 70 hours (on standby, e.g. not in use).When should I charge the batteries?You need to charge the batteries when you installa new battery or the wireless mic units red lightflashes. Regularly place the mics back on the baseunit to charge ready for your next call.How long does it take to charge the batteries?Allow up to eight hours to charge a unit’s batteryfrom empty.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp13

14Getting to know your conferencing unitLight status indicatorsWireless mic unitOn the base Steady red when charging.Steady amber when fully charged.No indication when charging in off-hook status.Flashes red and green alternately during registration.Off thebaseFlashes green when there’s an incoming call.Steady green during a call.Flashes amber and green alternately if battery low during a call.Steady red when Mute is on during a call.Flashes amber and red alternately if battery low when the callis muted.Flashes red when the wireless mic unit has a low battery.Light is off when the wireless mic unit is in idle mode or withouta battery.Flashes amber slowly when the wireless mic unit is outof range or not registered.Steady red during de-registration of the wireless mic.Base unitIncoming call Flashes green.On a callSteady green.Steady red when Mute is on.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

Getting to know your conferencing unitMenu mapPhonebookPhonebook emptyORPhonebook ListCalls ListCalls List emptyORCalls List EntriesRinger VolumeRingersSet Date/TimeEdit ContactAdd ContactDeleteDelete AllSpeed DialCapacityStore To PBDeleteDelete All CallsEdit NumberEnter NumberDelete Contact?Delete All Contacts?1-5Delete All Calls?6 levelsOffRinger ToneTone 1-10Set DateSet TimeTime Format12-Hour24-HourPage All MicsSettingsDate FormatRename BaseDD/MM/YYMM/DD/YYKey Tone3 levelsOffDial ModeTonePulsePBX ModeOnOffAccess Code:Access CodeResetReset To Default?If you need some help, call us on 0800 218 2182* or go to bt.com/producthelpEdit NameEnter NameEditDelete15

16Using your conferencing unitMake a call1. Press.2. When you hear the dial tone, enter the number.Preparatory dialling1. Dial the number first. If you make a mistake,press the button to delete the last digit.2. Pressbutton to dial.Answer a callPress.End a callPress– and remember to put any wireless micunits on the base unit.Redial last callPressand then.Adjust volumeDuring a call, pressto increase or decrease thevolume. You’ll hear two beeps when the highest orlowest volume is reached.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

Using your conferencing unitMute1. During a call, pressto mute all microphones inthe system.again to unmute all microphones in2. Pressthe system.During a call, you can talk tosomeone nearby without yourcaller hearing.Silence the ringerIf you don’t want to be disturbed, you can stop thephone from ringing when a call comes in. Pressseveral times until you see Ringer Off.button on the base unit.Or, just press theCall waitingIf you’ve got a call waiting service and it is switchedon, you hear a beep while you’re on a call so youknow that another call is trying to get through.Pressto hold the call you’re on and answer theagain to switch between thenew call. Presstwo calls.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp17

18Using your conferencing unitRedial listAbout the redial listYour conferencing unit stores the last ten phonenumbers dialled.See the redial listSee the redial list to find out who called, to returnthe call or to copy the caller’s name and number toyour phonebook.1. Presswhen the base unit isn’t in use.2. Press or to scroll the redial list or pressrepeatedly to scroll down the list.Dial a redial list entry1. Presswhen the base unit isn’t in use.2. Press or to scroll to find the number you’relooking for.3. To dial, pressSave a redial list entry to your phonebook1. Find the number in your redial list (see See theredial list above) and press .2. Press or to scroll to find Store To PB, and thenpress . The base unit shows Edit Number.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

Using your conferencing unit3. When the number shows, press . Use your keypadto edit the number: press or to move the cursor to the left or right press to delete a number press and hold to delete all numbers.4. Press . The base unit will show Enter Name.Use your keypad to edit the name: press or to move the cursor to the left or right press to add a space press to delete a character press and hold to delete all characters.5. Press to save.Delete a redial list entry1. Find the number in your redial list (see See theredial list on page 18) and press .2. Press or to scroll to Delete, and then pressSee page 22 for the fullcharacter map.Delete all redial list entries1. Find the number in your redial list (see See theredial list on page 18) and press .2. Press or to scroll to Delete All, and thenpress .If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp19

20Using your conferencing unitPressto exit thephonebook, calls list or rediallist when you’re on a call.How to get a number from the calls list orphonebook, whilst on a call1. Press .2. Press or to scroll to Calls List or Phonebookthen press .3. Press or to scroll to find the number you want.How to get a number from the redial list while ona call1. Press.2. Press or to scroll to find the number you want.If you get an incomingcall while you are paging themics, the incoming call willtake priority and the pagingwill stop.If you want to cancel thepaging at any time press.Page all microphonesYou can page the mics to help you locate them.1. Press when the base isn’t in use.2. Press or to scroll and find Page All Mics, thenpress .3. All registered mics in range will beep for60 seconds.button on4. To stop the paging beep, press thethe base, or to mute individual mics, pressonthe selected mic, or place it back in the cradle.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

Phonebook1.2.3.4.5.Add a phonebook entryHere’s how to find letters when making an entry inthe phonebook using the keypad: press a key andyou’ll get that key’s first character (e.g. ‘A’), pressagain and you’ll get the next (e.g. ‘B’) etc.The first letter of every word you enter will bea capital letter.Press when the base unit isn’t in use, then .Press or to scroll and find Add Contact, thenpress .When the screen shows Enter Number use yourkeypad to enter the number, then press .When the screen shows Enter Name use yourkeypad to enter the name. press or to move the cursor to the left or right press to add a space press to delete a character press and hold to delete all characters.Press to save.21See the full character map onpage 22.Numbers can be up to 30 digits.Names can be up to15 characters.To insert a Pause (P), press andhold .If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

22PhonebookCharacter mapKey Character key press repetitionTo insert a Pause (P), press andhold .1 2 3 4 5 6 7 8 9 10 11 no67PQRSpqrs78TUVtuv89WXYZwxyz90Space 0,*#Search your phonebookYou can search alphabetically.1. Press when the base unit isn’t in use.2. Press or to scroll through your phonebook oruse your keypad to enter the first digit of the nameyou’re looking for. If there isn’t anything matchingyour search, you’ll see the closest result.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

PhonebookCall someone in your phonebookFind a name in your phonebook (see Search your.phonebook on page 22) and press1.2.3.4.5.Edit a phonebook entryPress when the base unit isn’t in use, thenpress .Press or to scroll and find Edit Contact, thenpress . The base unit will show Edit Number.Use your keypad to edit the number: press or to move the cursor to the left or right press to delete a number press and hold to delete all numbers.Press . The base unit will show Edit Name.Use your keypad to edit the name: press or to move the cursor to the left or right press to add a space press to delete a character press and hold to delete all characters.Press to save.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp23

24PhonebookAdd phonebook entry to speed dialYou can copy up to ten phonebook entries (up to 12characters each) to your speed dial locations (1-5).1.2.3.4.5.Save a speed dial entryFind a name in your phonebook (see Search yourphonebook on page 22) and press .Press or to scroll and find Speed Dial, thenpress .Press or to scroll and find the speed diallocation (1-5) you want.Press to show your selected phonebook entry.Press to save.Dial a speed dial numberWhen the base unit isn’t in use, press and holdto dial the number stored on that speed dial.toIf you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

PhonebookDelete a speed dial entry1. Find a name in your phonebook (see Search yourphonebook on page 22) and press .2. Press or to scroll and find Speed Dial, thenpress .3. Press or to scroll and find the speed dial location(1-5) you want to change and press twice.4. Press or to scroll and select Delete, and thenpress .If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp25

26Caller Display and the calls listYou’ll need to subscribe toyour network provider’s CallerDisplay service for this featureto work. You might have to paya fee. For more information onBT Calling Features, call BT freeon 0800 800 150.About caller displayYour conferencing unit supports caller display(type 1) service. Caller display information mightnot be available for every incoming call. Callersmight block their names and/or phone numbers.To make sure the caller’s nameis displayed, make sure you’vestored the full telephonenumber in your phonebook,including the dialling code.Calls listIf you use a caller display service, information abouteach caller will show after the first or second ring.If you answer a call before the caller’s informationappears, it won’t be saved in the calls list.The calls list stores up to 50 entries, each up to16 digits for the phone number and 15 charactersfor the name. When the calls list is full, the oldestentry is deleted to make room for new incomingcall information.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

Caller Display and the calls listView and dial from the calls listYou can review the calls list to find out who called,to return the call, or to copy the caller’s name andnumber into your phonebook.1. Press when the base unit isn’t in use.2. Press or to browse your entries.3. To dial an entry, presswhen the entry is displayed.Missed call notificationIf an incoming call has beenmissed (i.e. not answered), amissed call notification will bedisplayed on the idle screen.To clear the notification youneed to go into the calls list andview the missed call.Delete a calls list entry / all entries1. Press when the base unit isn’t in use then .3. Press or to scroll and find Delete or Delete AllCalls and press .Caller display screen messagesShowsWhenPRIVATE CALLERThe caller information is hiddenby the callerUNKNOWN CALLERThe caller information isn’tprovided by the networkIf you need some help, call us on 0800 218 2182* or go to bt.com/producthelp27

28SettingsHow to change your settingsUsing the menu to change settingsYou can use the main menu on your base unit tochange the phone settings (see the menu map onpage 15). The sort of things you can change areringer volume and tone, date and time, base unitname, key tone, dial mode and PBX code. You canalso reset the default settings.1.2.3.4.MenuHow to enter the menuPress when the base unit isn’t in use.Press or to scroll to find what you’relooking for.Press to select the item.Press to go back.VolumeHow to adjust the ringer volumeHere’s how to increase or decrease ringer volume.1. Pressorwhen the base unit isn’t in use tofind the volume level you want.2. Press to save.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

Settings1.2.3.4.5.Here’s how to turn ringer offPress when the base unit isn’t in use.Press or to scroll and find Ringers, then press .Press again.Press to scroll and find Ringer Off.Press to save. Your base unit will now not ring forall incoming calls.1.2.3.Ringer toneHow to change your ringer toneYou’ve got a selection of ringer tones to choosefrom. Here’s how to change your ringer tone.Press when the base unit isn’t in use.Press or to scroll and find Ringers, then press .Press or to scroll and find Ringer Tone, thenpress .Press or to scroll and try each ringer tone(Tone 1 to Tone 10).Press to save the tone you want.4.5.The default ringer tone is Tone 1.If you select a differentpolyphonic ringer tone(i.e. from Tones 6-10) andyou have another telephoneconnected to the sametelephone line, then your X300could continue to ring for awhile after the call is answeredby the parallel telephone.To overcome this problem,select a ringer from Tones 1-5.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp29

30Settings1.2.3.4.5.6.7.8.9.Date and timeHow to change the date and timePress when the base unit isn’t in use.Press or to scroll and find Set Date/Time,then press .Press or to scroll and find the date, then press, or use the keypad to enter a two-digit number(01-31).Press or to scroll and find the month, thenpress , or use the keypad to enter a two-digitnumber (01-12).Press or to scroll and find the year, then press, or use the keypad to enter a two-digit number(00-99) and press .Press or to scroll and find the hour, then press, or use the keypad to enter a two-digit number(01-24).Press or to scroll and find the minute, thenpress , or use the keypad to enter a two-digitnumber (00-59).Press or to scroll and find AM or PM.Press to save.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

Settings1.2.3.4.5.Base unitHow to rename your base unitYour unit’s new name can be up to 11characters long.Press when the base unit isn’t in use.Press or to scroll and find Settings, thenpress .Press or to scroll and find Rename Base, thenpress .The base unit will show the default name BASE.Enter your new name using the keypad: Press or to move the cursor to the left or right. Press to delete a character. Press and hold to delete all characters.Press to save.The base unit will show thedefault name BASE or theexisting name if it’s alreadybeen changed.See the full character map onpage 22.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp31

32Settings1.2.3.4.5.Key toneHow to turn off or adjust your key tone volumeThe key tone is the beep you hear every time youpress the keypad. It’s easy to turn this off.Press when the base unit isn’t in use.Press or to scroll and find Settings, thenpress .Press or to scroll and find Key Tone, thenpress .Press or to scroll and try each tone(Off, or 1 to 3).Press to save.Dial mode1.2.3.4.5.How to change your dial modeThe dial mode is preset to tone dialing. If you have apulse service, you need to change the dial mode topulse dialing before making a call.Press when the base unit isn’t in use.Press or to scroll and find Settings, then press .Press or to scroll and find Dial Mode, thenpress .Press Tone or Pulse.Press to save.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

SettingsPBX modeThe conferencing unit is set by default toPBX Mode On.If you’re using the unit on a PBX1 then this modeis correct.If you’re using the unit on a PSTN2 line you will needto change the setting to PBX Mode Off.1.2.3.4.1PBX Private Branch Exchange(switchboard)2PSTN Public SwitchedTelephone Network(analogue telephone line)Turn PBX offPress when the base isn’t in use.Press to scroll and find Settings, then press .Pressto scroll and find PBX Mode, then press .Press orto select Off and press .If in any doubt of the correct PBX setting, contactyour PBX Network Manager.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp33

34SettingsInternal switchboard numbersare unlikely to need a prefixaccess code, so the access codeis only automatically insertedwhen dialling from the Calls list.1.2.3.4.The PBX On/Off setting andthe Access code setting are notdirectly linked (i.e. if you setan access code, then this digitwill be dialled from the Callslist, even when the PBX is setto Off).Set an access codeIf you’re connected to a switchboard, you mightneed to enter an access code (e.g. 9) before eachnumber is dialled. Your conferencing unit can storean access code which is automatically dialled beforeeach number, but only when you are in the Calls list.Press when the base isn’t in use.Press or to scroll and find Settings, thenpress .Press or to scroll and find Access Code, thenpress .Enter the number you want (maximum 1 digit) andpress .When you make a call from the Phonebook, Speeddial, Redial list or when pre-dialling, this accesscode feature just inserts a pause after the firstnumber during dialling, so that the number can bedialled correctly, providing the first number dialledmatches the stored access code number. (Pleasenote it does not insert the code itself e.g. 9).If you wish to use this feature for dialling, whenyou’re NOT in the Calls list, then you need to addthe one-digit prefix access code (e.g. 9) to each ofyour Phonebook entries.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

SettingsReset1.2.3.4.How to reset to default settingsYour phonebook and speed dial entries won’t bedeleted if you reset your settings.Press when the base unit isn’t in use.Press or to scroll and find Settings, thenpress .Press until the base unit shows Reset, and thenpress .The base unit shows Reset To Default? Press .If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp35

36SettingsIf you wish to stop the processyou can press thebutton.If registration fails, you will seethe error message ‘Registrationfailed. Try again’. Please followthe steps again.1.2.3.4.5.De-register and re-register the wireless micsIf you have purchased an additional wireless micyou will need to de-register and then re-register allthe mics before you can use them.When the conferencing unit is in idle mode, put allreplacement/working mics on the base unit.Enter the code *331734# and press on thebase unit.The display will show ‘Please Place All WirelessMics On Cradle, Then Press OK’.Wait for the base to go through the de-registrationand registration process.Once the process has been successful, the displaywill show ‘Registration done’ and you will heara confirmation tone.If you need some help, call us on 0800 218 2182* or go to bt.com/producthelp

Help37Conferencing unit doesn’t work Make sure all cables are plugged in correctly and that any batteries are installedand charged. After you’ve finished using your wireless mics on a call, rememberto put them back on the base so they can charge.There’s no dial tone Make sure all cabl

numbers, press to move the cursor to the right. Phone Book or When idle, press to see phonebook (see page 21). In menu, phonebook, calls or redial list, press to scroll down. When entering names or numbers, press to move the cursor to the left. R Press R to answer an incoming call during a